We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
MDO-2000E series Specifications | ||||||
| MDO-2072EG(X) | MDO-2074EG(X) | MDO-2102EG(X) | MDO-2104EG(X) | MDO-2202EG(X) | MDO-2204EG(X) |
Channels | 2ch+Ext | 4ch | 2ch+Ext | 4ch | 2ch+Ext | 4ch |
Bandwidth | DC~70MHz | DC~70MHz | DC~100MHz | DC~100MHz | DC~200MHz | DC~200MHz |
(-3dB) | (-3dB) | (-3dB) | (-3dB) | (-3dB) | (-3dB) | |
Rise time | 5ns | 5ns | 3.5ns | 3.5ns | 1.75ns | 1.75ns |
Bandwidth Limit | 20MHz | 20MHz | 20MHz | 20MHz | 20M/100MHz | 20M/100MHz |
Vertical Sensitivity | ||||||
Resolution | 8 bit | |||||
1mV~10V/div | ||||||
Input Coupling | AC, DC, GND | |||||
Input Impedance | 1MΩ// 16pF approx. | |||||
DC Gain Accuracy | ±(3%)when 2mV/div or greater is selected | |||||
±(5%)when 1mV/div is selected; | ||||||
Polarity | Normal & Invert | |||||
Maximum Input Voltage | 300Vrms, CAT I | |||||
Offset Position Range | 1mV/div ~ 20mV/div : ±0.5V | |||||
50mV/div ~ 200mV/div : ±5V | ||||||
500mV/div ~ 2V/div : ±25V | ||||||
5V~10V/div : ±250V | ||||||
Waveform Signal Process | +, -, ×, ÷, FFT, User Defined Expression. | |||||
| FFT:1Mpts | |||||
Trigger | ||||||
Source | CH1 ,CH2, CH3, CH4, Line, EXT* | |||||
*dual channel models only | ||||||
Trigger Mode | Auto (supports Roll Mode for 100 ms/div and slower), Normal, Single Sequence | |||||
Trigger Type | Edge, Pulse Width(Glitch), Video, Pulse Runt, Rise & Fall(Slope), Alternate,tme out, Event-Delay(1~65535 events), Time-Delay(Duration,4nS~10S), Bus | |||||
Holdoff range | 4ns~10s | |||||
Coupling | AC,DC,LF rej. ,HF rej. ,Noise rej. | |||||
Sensitivity | 1div | |||||
External Trigger | ||||||
Range | ±15V | |||||
Sensitivity | DC ~ 100MHz Approx. 100mV | |||||
100MHz ~ 200MHz Approx. 150mV | ||||||
Input Impedance | 1MΩ±3%~16pF | |||||
Horizontal | ||||||
Time base Range | 1ns/div ~ 100s/div (1-2-5 increments) | |||||
ROLL: 100ms/div ~ 100s/div | ||||||
Pre-trigger | 10 div maximum | |||||
Post-trigger | 2,000,000 div maximum. | |||||
Time base Accuracy | ±50 ppm over any ≥ 1 ms time interval | |||||
Real Time Sample Rate | Max.:1GSa/s (4ch model) | |||||
Record Length | Per Channel 10M pts | |||||
Acquisition Mode | Normal, Average, Peak Detect, Single | |||||
Peak Detection | 2ns (typical) | |||||
Average | selectable from 2 to 256 | |||||
X-Y Mode | ||||||
X-Axis Input | Channel 1; Channel 3* | |||||
*four channel models only | ||||||
Y-Axis Input | Channel 2; Channel 4* | |||||
| *four channel models only | |||||
Phase Shift | ±3° at 100kHz | |||||
Cursors and Measurement | ||||||
Cursors | Amplitude, Time, Gating available;Unit:Seconds(s),Hz(1/s) ,Phase(degree) ,Ration(%) | |||||
Automatic Measurement | 38 sets: Pk-Pk, Max, Min, Amplitude, High, Low, Mean, Cycle Mean, RMS, Cycle RMS, Area, Cycle Area, ROVShoot, FOVShoot, RPREShoot, FPREShoot, Frequency, Period, RiseTime, FallTime, +Width, -Width, Duty Cycle, +Pulses, -Pulses, +Edges, -Edges, %Flicker ,Flicker Idx,FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF, Phase | |||||
Control Panel Function | ||||||
Auto counter | 6 digits, range from 2Hz minimum to the rated bandwidth | |||||
Autoset | Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo Autoset | |||||
Save Setup | 20 sets | |||||
Save Waveform | 24 sets | |||||
Display | ||||||
TFT LCD Type | 8" TFT LCD WVGA color display | |||||
Display Resolution | 800 horizontal × 480 vertical pixels (WVGA) | |||||
Interpolation | Sin(x)/x | |||||
Waveform Display | Dots, vectors, variable persistence (16ms~4s), infinite persistence | |||||
Waveform Update Rate | 120,000 waveforms per second, maximum | |||||
Display Graticule | 8 x 10 divisions | |||||
Display mode | YT ;XY | |||||
Interface | ||||||
USB Port | USB 2.0 High-speed host port X1, USB 2.0 High-speed device port X1 | |||||
Ethernet(LAN) Port | RJ-45 connector, 10/100Mbps with HP Auto-MDIX | |||||
Go-NoGo BNC | 5V Max/10mA TTL open collector output | |||||
Kensington Style Lock | Rear-panel security slot connects to standard Kensington-style lock. | |||||
Spectrum Analyzer Specifications | ||||||
Frequency range | DC~500MHz (Max. ,Max.bandwidth~500MHz uncalibrated) | |||||
Span | 1kHz~500MHz(Max.) | |||||
Resolution bandwidth | 1Hz ~ 500kHz(Max.) | |||||
Reference level | -50 dBm to +40dBm in steps of 5dBm | |||||
Vertical units | dBV RMS; Linear RMS; dBm | |||||
Vertical position | -12divs to +12divs | |||||
Vertical scale | 1dB/div to 20dB/div in a 1-2-5 Sequence | |||||
Display average noise level | 1V/div < -50dBm, Avg : 16 | |||||
Spurious response | 2nd harmonic distortion< 40dBc | |||||
Frequency domain trace types | Normal ; Max Hold ; Min Hold ; Average (2 ~ 256) | |||||
Detection methods | Sample ; +Peak ; -Peak ; Average | |||||
FFT Windows | FFT Factor : | |||||
Hanning 1.44 | ||||||
Rectangular 0.89 | ||||||
Hamming 1.30 | ||||||
Blackman 1.68 | ||||||
AWG Specifications | ||||||
Channels | 2 | |||||
Sample Rate | 200 Msa/s | |||||
Vertical Resolution | 14 bits | |||||
Max. Frequency | 25 MHz | |||||
Waveforms | Sine, Square, Pulse, Ramp, DC, Noise, Sinc, Gaussian, Lorentz, Exponential Rise, Exponential Fall, Haversine, Cardiac | |||||
Output Range | 20 mVpp to 5 Vpp, HighZ;10 mVpp to 2.5 Vpp, 50 Ω | |||||
Output Resolution | 1mV | |||||
Output Accuracy | 2% (1 kHz) | |||||
Offset Range | ±2.5 V, HighZ;±1.25 V, 50 Ω | |||||
Offset Resolution | 1mV | |||||
Sine | ||||||
Frequency Range | 100mHz to 25MHz | |||||
Flatness | ±0.5 dB( relative to 1kHz) | |||||
Harmonic Distortion | -40 dBc | |||||
Stray (Non-harmonic) | -40 dBc | |||||
Total Harmonic Distortion | 1% | |||||
S/N Ratio | 40 dB | |||||
Square/Pulse | ||||||
Frequency Range | 100 mHz to 15MHz | |||||
Rise/Fall time | <15ns | |||||
Overshoot | <3% | |||||
Duty cycle | Square:50%;Pulse:0.4%~99.6% | |||||
Min. Pulse Width | 30 ns | |||||
Jitter | 500 ps | |||||
Ramp | ||||||
Frequency Range | 100mHz~1MHz | |||||
Linearity | 1% | |||||
Symmetry | 0 to 100% | |||||
DMM Specifications (MDO-2000EX only) | ||||||
| 5,000 counts | |||||
CAT II 600Vrms, CAT III 300Vrms | ||||||
DC VOLTAGE | 50mV, 500mV, 5V, 50V, 500V, 1000V 6 ranges | |||||
Accuracy | 50mV, 500mV, 5V, 50V, 500V, 1000V ±(0.1% reading + 5 digits) | |||||
Input Impedance | 10MΩ | |||||
DC CURRENT | 50mA, 500mA, 10A 3 ranges | |||||
Accuracy | 50mA - 500mA ±(0.5% reading + 0.05mA) 10A ±(0.5% reading + 50mA) | |||||
AC VOLTAGE | 50mV, 500mV, 5V, 50V, 700V 5 ranges | |||||
Accuracy | 50mV, 500mV, 5V, 50V, 700V ±(1.5% reading + 15 digits) at 50Hz-1kHz * Amplitude greater than 0.2% of the full scale reading. | |||||
AC CURRENT | 50mA, 500mA, 10A 3 ranges | |||||
Accuracy | 50mA, 500mA, ±(1.5% reading + 0.05mA) at 50Hz-1kHz 10A ±(3% reading + 50mA) at 50Hz-1kHz * Measure range: >10mA | |||||
RESISTANCE | 500Ω, 5kΩ, 50kΩ, 500kΩ, 5MΩ, 5 ranges | |||||
Accuracy | 500Ω, 5kΩ, 50kΩ, 500kΩ ±(0.3% reading + 3 digits) 5MΩ ±(0.5% reading + 5 digits) | |||||
Power supply Specifications (MDO-2000EX only) | ||||||
Output Channel | CH1 & CH2 | |||||
Output voltage range | 1.0V~5.0V | |||||
Output Current (Max.) | 1A | |||||
Voltage Step | 0.1V Continuously Adjustable | |||||
output Voltage Accuracy | ±3% | |||||
Ripple and Noise | 50mVrms | |||||
Miscellaneous | ||||||
Multi-language menu | Available | |||||
operation environment | Temperature: 0°C to 50°C. Relative Humidity ≤ 80% at 40°C or below; ≤ 45% at 41°C ~ 50°C. | |||||
On-line help | Available | |||||
Time clock | Time and Date ,Provide the Date/Time for saved data | |||||
Dimensions | 384mmX208mmX127.3mm | |||||
Weight | 3kg |