GW Instek MDO-2102EX 100 MHz 2-Channel Mixed-Domain Oscilloscope

MDO-2000E series Specifications

MDO-2072EG(X)

MDO-2074EG(X)

MDO-2102EG(X)

MDO-2104EG(X)

MDO-2202EG(X)

MDO-2204EG(X)

Channels

2ch+Ext

4ch

2ch+Ext

4ch

2ch+Ext

4ch

Bandwidth

DC~70MHz

DC~70MHz

DC~100MHz

DC~100MHz

DC~200MHz

DC~200MHz

(-3dB)

(-3dB)

(-3dB)

(-3dB)

(-3dB)

(-3dB)

Rise time

5ns

5ns

3.5ns

3.5ns

1.75ns

1.75ns

Bandwidth Limit

20MHz

20MHz

20MHz

20MHz

20M/100MHz

20M/100MHz

Vertical Sensitivity

Resolution

8 bit

1mV~10V/div

Input Coupling

AC, DC, GND

Input Impedance

1MΩ// 16pF  approx.

DC Gain Accuracy

±(3%)when 2mV/div or greater is selected

±(5%)when 1mV/div is selected;

Polarity

Normal & Invert

Maximum Input Voltage 

300Vrms, CAT I

Offset Position Range

1mV/div ~ 20mV/div : ±0.5V

50mV/div ~ 200mV/div : ±5V

500mV/div ~ 2V/div : ±25V

5V~10V/div : ±250V

Waveform Signal Process

 +, -, ×, ÷, FFT, User Defined Expression.

FFT:1Mpts
FFT:Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning, or Blackman.

Trigger

Source

CH1 ,CH2, CH3, CH4, Line, EXT*

*dual channel models only

Trigger Mode

Auto (supports Roll Mode for 100 ms/div and slower), Normal, Single Sequence

Trigger Type

Edge, Pulse Width(Glitch), Video, Pulse Runt, Rise & Fall(Slope), Alternate,tme out, Event-Delay(1~65535 events), Time-Delay(Duration,4nS~10S), Bus

Holdoff range

4ns~10s

Coupling

AC,DC,LF rej. ,HF rej. ,Noise rej.

Sensitivity

1div

External Trigger 

Range

±15V

Sensitivity

DC ~ 100MHz Approx. 100mV

100MHz ~ 200MHz Approx. 150mV

Input Impedance

1MΩ±3%~16pF

Horizontal

Time base Range

1ns/div ~ 100s/div (1-2-5 increments)

ROLL: 100ms/div ~ 100s/div

Pre-trigger

10 div maximum

Post-trigger

2,000,000 div maximum. 

Time base Accuracy

±50 ppm over any ≥ 1 ms time interval

Real Time Sample Rate

Max.:1GSa/s (4ch model)     
Per channel 1GSa/s (2ch model)                                         

Record Length

Per Channel 10M pts

Acquisition Mode

Normal, Average, Peak Detect, Single

Peak Detection

2ns (typical)

Average

selectable from 2 to 256

X-Y Mode

X-Axis Input

Channel 1; Channel 3*

*four channel models only

Y-Axis Input

Channel 2; Channel 4*

*four channel models only

Phase Shift

±3° at 100kHz

Cursors and Measurement

Cursors

Amplitude, Time, Gating available;Unit:Seconds(s),Hz(1/s) ,Phase(degree) ,Ration(%)

Automatic Measurement

38 sets: Pk-Pk, Max, Min, Amplitude, High, Low, Mean, Cycle Mean, RMS, Cycle RMS, Area, Cycle Area, ROVShoot, FOVShoot, RPREShoot, FPREShoot, Frequency, Period, RiseTime, FallTime, +Width, -Width, Duty Cycle, +Pulses, -Pulses, +Edges, -Edges, %Flicker ,Flicker Idx,FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF, Phase

Control Panel Function

Auto counter

6 digits, range from 2Hz minimum to the rated bandwidth

Autoset

Single-button, automatic setup of all channels for vertical, horizontal and trigger systems, with undo Autoset

Save Setup

20 sets

Save Waveform

24 sets

Display

TFT LCD Type

8" TFT LCD WVGA color display

Display Resolution

800 horizontal × 480 vertical pixels (WVGA)

Interpolation

Sin(x)/x

Waveform Display

Dots, vectors, variable persistence (16ms~4s), infinite persistence

Waveform Update Rate

120,000 waveforms per second, maximum

Display Graticule

8 x 10 divisions

Display mode

YT ;XY

Interface

USB Port

USB 2.0 High-speed host port X1, USB 2.0 High-speed device port X1

Ethernet(LAN) Port

RJ-45 connector, 10/100Mbps with HP Auto-MDIX

Go-NoGo BNC

5V Max/10mA TTL open collector output

Kensington Style Lock

Rear-panel security slot connects to standard Kensington-style lock.

Spectrum Analyzer Specifications

Frequency range

DC~500MHz (Max. ,Max.bandwidth~500MHz uncalibrated)

Span

1kHz~500MHz(Max.)

Resolution bandwidth

1Hz ~ 500kHz(Max.)

Reference level

 -50 dBm to +40dBm in steps of 5dBm

Vertical units

dBV RMS; Linear RMS; dBm

Vertical position

 -12divs to +12divs

Vertical scale

1dB/div to 20dB/div in a 1-2-5 Sequence

Display average noise level

1V/div < -50dBm, Avg : 16
100mV/div  < -70dBm, Avg : 16
10mV/div  < -90dBm, Avg : 16

Spurious response

2nd harmonic distortion< 40dBc
3rd harmonic distortion< 45dBc

Frequency domain trace types

Normal ; Max Hold ; Min Hold ; Average (2 ~ 256)

Detection methods

Sample ; +Peak ; -Peak ; Average

FFT Windows

FFT Factor :

Hanning 1.44

Rectangular 0.89

Hamming 1.30

Blackman 1.68

AWG Specifications

Channels

2

Sample Rate

200 Msa/s

Vertical Resolution

14 bits

Max. Frequency

25 MHz

Waveforms

Sine, Square, Pulse, Ramp, DC, Noise,  Sinc, Gaussian, Lorentz, Exponential Rise, Exponential Fall, Haversine, Cardiac

Output Range

20 mVpp to 5 Vpp, HighZ;10 mVpp to 2.5 Vpp, 50 Ω

Output Resolution

1mV

Output Accuracy

2% (1 kHz)

Offset Range

±2.5 V, HighZ;±1.25 V, 50 Ω

Offset Resolution

1mV

Sine

Frequency Range

100mHz to 25MHz

Flatness

±0.5 dB( relative to 1kHz)

Harmonic Distortion

-40 dBc

Stray (Non-harmonic)

-40 dBc

Total Harmonic Distortion

1%

S/N Ratio

40 dB

Square/Pulse

Frequency Range

100 mHz to 15MHz

Rise/Fall time

<15ns

Overshoot

<3%

Duty cycle

Square:50%;Pulse:0.4%~99.6%

Min. Pulse Width

30 ns

Jitter

500 ps

Ramp

Frequency Range

100mHz~1MHz

Linearity

1%

Symmetry

0 to 100%

DMM Specifications (MDO-2000EX only)

 
DIGIT LEVEL 

5,000 counts  

CAT II 600Vrms, CAT III 300Vrms

DC VOLTAGE 

50mV, 500mV, 5V, 50V, 500V,  1000V  6 ranges      

Accuracy

50mV, 500mV, 5V, 50V, 500V, 1000V ±(0.1% reading + 5 digits)

Input Impedance 

10MΩ      

DC CURRENT 

50mA, 500mA,  10A   3 ranges     

Accuracy

50mA - 500mA  ±(0.5% reading + 0.05mA)

10A  ±(0.5% reading + 50mA)

AC VOLTAGE

 50mV, 500mV, 5V, 50V, 700V  5 ranges     

Accuracy

50mV, 500mV, 5V, 50V, 700V ±(1.5%  reading + 15 digits) at 50Hz-1kHz

* Amplitude greater than 0.2% of the full scale reading.

AC CURRENT

50mA, 500mA, 10A 3 ranges      

Accuracy

50mA, 500mA, ±(1.5% reading + 0.05mA)  at 50Hz-1kHz

10A ±(3% reading + 50mA)  at 50Hz-1kHz 

* Measure range: >10mA

RESISTANCE

500Ω, 5kΩ, 50kΩ, 500kΩ, 5MΩ, 5 ranges      

Accuracy

500Ω, 5kΩ, 50kΩ, 500kΩ ±(0.3%  reading + 3 digits)

5MΩ ±(0.5%  reading + 5 digits)

Power supply Specifications (MDO-2000EX only)

Output Channel

CH1 & CH2

Output voltage range

1.0V~5.0V

Output Current (Max.)

1A

Voltage Step

0.1V Continuously Adjustable

output Voltage Accuracy 

±3%

Ripple and Noise

50mVrms

Miscellaneous

Multi-language menu

Available

operation environment    

Temperature: 0°C to 50°C. Relative Humidity ≤ 80% at 40°C or below; ≤ 45% at 41°C ~ 50°C.

On-line help

Available

Time clock

Time and Date ,Provide the Date/Time for saved data

Dimensions

384mmX208mmX127.3mm

Weight

3kg