We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
The Fluke Networks 30800009 TS30 test set has the same features as the 30800001 but instead of coming with piercing pin clips the 30800009 come with Angled Bed-of-Nails (ABN) clips.
Electrical | |
Return Loss | >14 dB (ref 600 Ω) |
Line Current Range | 15 mA to 120 mA |
Resistance to Continuous Current (Talk Mode) | 275 Ω typical at 20 mA |
Monitor Mode Impedance | >120,000 Ω 300 Hz to 3400 Hz |
Pulse Dial Output | |
Pulsing Rate | 10 pps ±1 pps |
Open/Close Ratio | 60/40 |
Inter-digit Interval | 800 ms +20%, -10% |
Resistance During Pulse Open | > 200,000 Ω |
Protection Against Alternating Current Overvoltage | The TS30 survives up to 300 Vrms across its test leads. |
Peak Acoustic Output of the Receiver | <120 dBspl |
DTMF Output Tone Frequencies Tone Frequency Error | per ITU-T Q.23 ±1.5% Maximum |
Tone Level | |
High Group Low Group | -4 dBm (into 600 Ω) -6 dBm (into 600 Ω) |
High vs Low Tone Difference | 2dB ±1db |
Last Number Redial (Tone/Pulse) | |
Memory Capacity Memory Retention | 23 digits 8-minutes nominal |
Flash Duration | 600 ms ±100 ms |
Ringer Loudness | > 70 dBA at 1 meter |
Ringer Equivalent (REN) | 0.14 |
Measurements | 10 in x 2.83 in x 3.34 in (25.5 cm x 7.2 cm x 8.5 cm) |
Weight | 16.8 ounces (0.476 kg) |
Environmental | |
Temperature Operating Storage | -4 °F to +140 °F (-20°C to +60°C) -40 °F to +151 °F (-40°C to +66°C) |
Relative Humidity | 5% to 95% |
Safety | |
Telecom Electrical | TNV-3 |
Safety Classification | IP54 |
Regulatory Standards Used | |
47 CFR Part 15, Subpart B ICES-003 Issue 3 AS/NZS 3548 EMC Directive 89/336/EEC, EN 55022:98, EN 61326:97, A1:98 Annex C, EN 61000-4-2, EN 61000-4-3 LV Directive 73/23/EEC, EN 610010.1 (1993) | |
Certifications and Compliance | |
Safety | |
IEC 61010-1:2010, Pollution Degree 2, Category: None Complies with CAN/CSA-C22.2 No. 61010-1 | |
EMC | |
IEC 61326-1 (Portable), IEC 61326-2-2, CISPR 11 (Group 1, Class A) Group 1 equipment: group 1 has intentionally generated and/or use conductively coupled radiofrequency energy which is necessary for the internal functioning of the equipment itself. Class A equipment is equipment suitable for use in all establishments other than domestic and those directly connected to a low voltage power supply network which supplies buildings used for domestic purposes. USA (FCC) – 47 CFR 15 subpart B, this product is considered an exempt device per clause 15.103 |
Notes: Specifications subject to change without notice. Legal requirements may exist regarding permission to connect equipment to a Telecom network operated by a public network operator.
Write Your Own Review