We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
Specifications | 4014B | 4040B |
Frequency Characteristics | ||
Sine | 0.01 Hz to 12 MHz | 0.01 Hz to 20 MHz |
Square | 0.01 Hz to 12 MHz | 0.01 Hz to 20 MHz |
Triangle | 0.01 Hz to 1 MHz | 0.01 Hz to 2 MHz |
Resolution | 6 digits* or 10 mHz | |
Accuracy | 0.01% ± 0.006 Hz | |
Output Characteristics | ||
Amplitude Range | 10 mVpp to 10 Vpp (into 50 Ω); 20 mVpp to 20 Vpp (open circuit) | |
Amplitude Resolution | 3 digits (1,000 counts) | |
Amplitude Accuracy | ± 2% ± 20 mV of programmed output from 1.01 V – 10 V | |
Flatness | ± 0.5 dB to 1 MHz ± 1 dB to 12 MHz | ± 0.5 dB to 1 MHz ± 1 dB to 20 MHz |
DC Offset Range | -4.99 V to 4.99 V (into 50 Ω) | |
DC Offset Resolution | 10 mV, 3 digits | |
DC Offset Accuracy | ± 2% ± 10 mV (into 50 Ω) | |
Output Impedance | 50 Ω ± 2% | |
Output Protection | Protected against short circuit or accidental voltage applied to the main output connector | |
Waveform Characteristics | ||
Harmonic Distortion (for sine wave at 5 Vp-p into 50 Ω) | 0 – 1 MHz, < -60 dBc 1 MHz – 5 MHz, <-50 dBc 5 MHz – 12 MHz, <-45 dBc | 0 – 1 MHz, < -60 dBc 1 MHz – 5 MHz, <-50 dBc 5 MHz – 12 MHz, <-45 dBc 12 MHz – 20 MHz, <-60 dBc |
Square Rise/Fall Time | ≤ 20 ns (10% to 90% at full amplitude into 50 Ω) | |
Duty Cycle | Square: 20% - 80% to 2 MHz Triangle: 1% - 99% in 1% steps, up to 200 kHz | |
Symmetry Accuracy at 50% | ± 1% | |
Jitter (square) | < 100 ps rms (cycle-to-cycle, typical) | |
Operating Modes | ||
Continuous | Output continuous at programmed parameters | |
Triggered | Output quiescent until triggered by an internal or external trigger, at which time one waveform cycle is generated to programmed parameters. Frequency of waveform cycle is limited to 1 MHz. | |
Gate |
- | Same as triggered mode, except waveform is executed for the duration of the gate signal. The last cycle started is completed. |
Burst | - | 2-65535 cycles |
Trigger Source | Trigger source may be internal, external, or manual. Internal trigger rate 0.1 Hz – 1 MHz (1 us – 10 s) | |
Modulation Characteristics | ||
Amplitude Modulation | ||
Internal | 0.1 Hz – 20 kHz sine only | 0.1 Hz – 20 kHz sine, square, or triangle waveform |
External | 5 Vp-p for 100% modulation, 10 kΩ input impedance | |
Frequency Modulation | ||
Internal | 0.1 Hz – 20 kHz sine only | 0.1 Hz – 20 kHz sine, square, or triangle waveform |
External | 5 Vp-p for 100% modulation, 10 kΩ input impedance | |
Sweep Characteristics | ||
Sweep Shape | Linear or Logarithmic, up or down | |
Sweep Time | 10 ms to 100 s | |
Input and Output | ||
Trigger IN | TTL compatible Maximum rate 1 MHz Input impedance 1 kΩ Minimum width > 50 ns | |
Sync OUT | TTL pulse at programmed frequency; 50 Ω source impedance | |
Modulation IN | 5 Vp-p for 100% modulation 10 kΩ input impedance DC to > 20 kHz minimum bandwidth | |
Counter Characteristics | ||
Range | 50 Hz to 50 MHz | |
Resolution | Auto ranging, up to 8 digits | |
Accuracy | ± 0.02% ± 2 digits | |
Sensitivity | 25 mVrms typical | |
General | ||
Memory Storage | 10 instrument settings | 20 instrument settings |
Power Requirements | 100 V – 240 V AC ± 10% | |
Operating Temperature | 32 °F to 122 °F (0 °C to 50 °C) | |
Storage Temperature | 14 °F to 158 °F (-10 °C to 70 °C) | |
Humidity | 95% R.H. 0 °C to 30 °C | |
Dimensions (W x H x D) | 8.39” x 3.46” x 8.27” (213 x 88 x 210 mm) | |
Weight | 5.5 lbs (2.5 kg) | |
Electromagnetic Compatibility | Meets EMC Directive 2004/108/EC, EN55011, EN55082 | |
Safety | Meets Low Voltage Directive 2006/95/EC, EN61010 | |
Three-Year Warranty | ||
Included Accessories | Instruction manual on CD, power cord, USB (type A to B) interface cable, certificate of calibration |
*For square wave, resolution is up to 4 digits when frequency is > 20 kHz.
Note: All specifications apply to the unit after a temperature stabilization time of 15 minutes over an ambient temperature range of 23 ºC ± 5 ºC.
Specifications are subject to change without notice.