CH1/ CH2 | |
Arbitrary Functions | | | |
| ARB function | Built-in |
| Sample Rate | 200 MSa/s |
| Repetition Rate | 100MHz |
| Waveform Length | 16k points |
| Amplitude Resolution | 14 bits |
| Non-Volatile Memory | 10sets 16k points(1) |
| User-defined output section | From point 2~16384 |
| User-defined output marker section | From point 2 ~ 16384 |
| Output mode | 1~1048575 cycles or infinite mode |
Frequency Characteristics | | | |
| Range | Sine | 60MHz(max) |
| | Square | 25MHz(max) |
| | Triangle, Ramp | 1MHz |
| Resolution | | 1μHz |
| AccuracyStability | ±20 ppm |
| Aging | ±1 ppm, per 1 year |
| Tolerance | ≤1μHz |
Output Characteristics(2) | | | |
| AmplitudeRange | 1mVpp to 10 Vpp (into 50Ω) 2mVpp to 20 Vpp (open-circuit) |
| Accuracy | ±2% of setting ±1 mVpp (at 1 kHz/into 50Ω without DC offset)) |
| Resolution | 0.1mV or 4 digits |
| Flatness | ± 1% (0.1dB) ≦1MHz ± 3% (0.3dB) ≦50 MHz ± 10% (0.9dB) ≦160MHz ± 30% (3dB) ≦320MHz (sinewave relative to 1 kHz/into 50Ω) |
| Units | Vpp, Vrms, dBm |
Offset | Range | ±5 Vpk ac +dc (into 50Ω) ±10Vpk ac +dc (Open circuit) |
| Accuracy | 1% of setting + 5mV+ 0.5% of amplitude |
Waveform Output | Impedance | 50Ω typical (fixed) > 10MΩ (output disabled) |
| Protection | Short-circuit protected Overload relay automatically disables main output |
| Ground Isolation | 42Vpk max |
Sync Output | Range | TTL-compatible into>1kΩ |
| Impedance | 50Ω standard |
| Ground Isolation | 42Vpk max |
Sine wave Characteristics(3) | | |
| Harmonic distortion | –60 dBc DC~200kHz, Ampl>0.1 Vpp –55 dBc 200kHz~1 MHz, Ampl>0.1 Vpp –45 dBc 1MHz~10 MHz, Ampl>0.1Vpp –30 dBc 10MHz~320MHz, Ampl>0.1Vpp |
| Total harmonic distortion | < 0.1% (Ampl>1Vpp)DC~100 kHz |
Square wave Characteristics | | |
| Rise/Fall Time | <15ns |
| Overshoot | <5% |
| Asymmetry | 1% of period +5 ns |
| Variable duty Cycle | 0.01% to 99.99%(limited by the current frequency setting) |
| Jitter | 20ppm+500ps(4) |
Ramp Characteristics | | | |
| Linearity | < 0.1% of peak output |
| Variable Symmetry | 0% to 100% |
Pulse Characteristics | | |
| Frequency | 1uHz~25MHz |
| Pulse Width | ≧20nS(limited by the current frequency setting) |
| Variable duty Cycle | 0.01%~99.99%(limited by the current frequency setting) |
| Overshoot | <5% |
| Jitter | 20ppm +500ps(4) |
Pulse Generator | | |
| Amplitude | 1mVpp to 2.5 Vpp (into 50Ω) 2mVpp to 5 Vpp (open-circuit) |
| Offset | ±1 Vpk ac +dc (into 50Ω) ±2Vpk ac +dc (Open circuit) |
| Frequency | 1uHz~25MHz |
| Pulse Width | 20nS~999.9ks(limited by the current frequency setting) |
| Variable duty Cycle | 0.01%~99.99%(limited by the current frequency setting) |
| Leading and Trailing Edge Time(5) | 10nS~20S(1ns resolution) (limited by the current frequency and pulse width settings) |
| Overshoot | <5% |
| Jitter | 100ppm +500ps(4) |
RF Generator | | |
Arbitrary Functions | | | |
| ARB function | Built-in |
| Sample Rate | 200 MSa/s |
| Repetition Rate | 100MHz |
| Waveform Length | 16k points |
| Amplitude Resolution | 14 bits |
| User-defined output section | From point 2~16384 (optional) |
| Jitter | 20ppm +5ns |
Frequency Characteristics | | | |
| Range | Sine | 1uHz~160MHz(MFG-2XXXMF) | 1uHz~320MHz(MFG-2XXXMR) |
|
| | Square | 25MHz(max) |
| | Triangle, Ramp | 1MHz |
| Resolution | | 1μHz |
| AccuracyStability | ±20 ppm |
| Aging | ±1 ppm, per 1 year |
| Tolerance | ≤1μHz |
Output Characteristics(2) | | | |
| Amplitude(into 50Ω) | 1mVpp to 2 Vpp (MFG-2XXXMF) 1mVpp to 1 Vpp (MFG-2XXXMR) |
| Accuracy | ±2% of setting ±1 mVpp (at 1 kHz/into 50Ω without DC offset)) |
| Resolution | 0.1mV or 4 digits |
| Flatness | ± 1% (0.1dB) ≦1MHz ± 3% (0.3dB) ≦50 MHz ± 10% (0.9dB) ≦160MHz ± 30% (3dB) ≦320MHz (sinewave relative to 1 kHz/into 50Ω) |
Offset | | ±1 Vpk ac +dc (into 50Ω) ±2Vpk ac +dc (Open circuit) |
Waveform Output | Impedance | 50Ω typical (fixed) > 10MΩ (output disabled) |
Sine wave Characteristics(3) | | |
| Harmonic distortion | –60 dBc DC~200kHz, Ampl>0.1 Vpp –55 dBc 200kHz~1 MHz, Ampl>0.1 Vpp –45 dBc 1MHz~10 MHz, Ampl>0.1Vpp –30 dBc 10MHz~320MHz, Ampl>0.1Vpp |
| Total harmonic distortion | < 0.1% (Ampl>1Vpp)DC~100 kHz |
Square wave Characteristics | | |
| Rise/Fall Time | <15ns |
| Overshoot | <5% |
| Asymmetry | 1% of period +5 ns |
| Variable duty Cycle | 0.01% to 99.99%(limited by the current frequency setting) |
| Jitter | 20ppm+500ps(4) |
Ramp Characteristics | | | |
| Linearity | < 0.1% of peak output |
| Variable Symmetry | 0% to 100% |
Modulation/Sweep | | |
| Modulation Type | AM,FM,PM,FSK,PWM (The detail same as CH1 modulation specification) |
| Sweep type | Frequency |
| Source | INT/EXT(INT only for AM,FM,PM, PWM) |
PSK | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp, Pulse |
| Modulating Waveforms | 50% duty cycle square |
| Internal Frequency | 2mHz to 1 MHz |
| Phase Range | 0∘~360.0∘ |
| Source | Internal / External |
ASK | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp, Pulse |
| Modulating Waveforms | 50% duty cycle square |
| Internal Frequency | 2mHz to 1 MHz |
| AmplitudeRange | 0%~100.0% |
| Source | Internal / External |
Power Amplifier | | |
| Input Impedance | 10KΩ |
| Input voltage | 1.25Vpmax |
| Working Mode | Constant Voltage |
| Gain | 20dB |
| Output Power (RL=8Ω) | 20W(Square) |
| Output Voltage | 12.5Vpmax |
| Output Current | 1.6Amax |
| Rise/Fall Time | <2.5uS |
| Full Power Bandwidth | DC-100KHz |
| Overshoot | 5% |
| Total harmonic distortion | < 0.1% (Ampl>1Vpp) 20Hz~20 kHz |
| Ground Isolation | 42Vpk max |
Advanced Functions | | |
AM Modulation | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp, Pulse, Arb |
| Modulating Waveforms | Sine, Square, Triangle,Upramp, Dnramp |
| Modulating Frequency | 2mHz to 20kHz (Int)DC to 20kHz (Ext) |
| Depth | 0% to 120.0% |
| Source | Internal / External |
FM Modulation | | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp |
| Modulating Waveforms | Sine, Square, Triangle,Upramp, Dnramp |
| Modulating Frequency | 2mHz to 20kHz (Int) DC to 20kHz (Ext) |
| Peak Deviation | DC to max frequency | |
| Source | Internal / External |
PM | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp |
| Modulating Waveforms | Sine, Square, Triangle, Upramp, Dnramp |
| Modulation Frequency | 2mHz to 20kHz (Int) DC to 20kHz (Ext) |
| Phase deviation | 0∘~360.0∘ |
| Source | Internal / External |
SUM | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp |
| Modulating Waveforms | Sine, Square, Triangle, Upramp, Dnramp |
| Modulation Frequency | 2mHz to 20kHz (Int) DC to 20kHz (Ext) |
| SUM depth | 0%~100.0% |
| Source | Internal / External |
PWM | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp |
| Modulating Waveforms | Sine, Square, Triangle, Upramp, Dnramp |
| Modulation Frequency | 2mHz to 20kHz (Int) DC to 20kHz (Ext) |
| Phase deviation | 0%~100.0% pulse width |
| Source | Internal / External |
FSK | | |
| Carrier Waveforms | Sine, Square, Triangle, Ramp, Pulse |
| Modulating Waveforms | 50% duty cycle square |
| Internal Frequency | 2mHz to 1 MHz |
| FrequencyRange | 1μHz to max frequency |
| Source | Internal / External |
Sweep | | | |
| Waveforms | Sine, Square, Triangle, Ramp |
| Type | Linear or Logarithmic |
| Sweep direction | Sweep up or sweep down |
| Start/Stop Freq | 1uHz to max frquency |
| Sweep Time | 1ms to 500s |
| Source | Internal / External |
| Trigger | Single, External, Internal. |
| Marker | Marker signal on falling edge(programmable) |
| Source | Internal / External |
Burst | | |
| Waveforms | Sine, Square, Triangle, Ramp |
| Frequency | 1uHz~Max Frequency |
| Pulse count | 1~1000000 Cycles or intfinite |
| Start/ Stop Phase | -360.0∘~+360.0∘ |
| Internal Frequency | 1 us~500 s |
| Gate source | External Trigger |
| Trigger Source | Single, External, Internal. |
Trigger Delay | NCycle, Infinite | 0s~100 s |
External Trigger Input | | | |
| Type | For FSK, Burst, Sweep |
| Input Level | TTL Compatibility |
| Slope | Rising or Falling(Selectable) |
| Pulse Width | >100ns |
| Input Impedance | 10kΩ,DC coupled |
External Modulation Input | | | |
| Type | For AM, FM, PM,SUM,PWM |
| Voltage Range | ±5V full scale |
| Input Impedance | 10kΩ |
| Frequency | DC to 20kHz |
| Ground Isolation | 42Vpk max |
Trigger Output | | | |
| Type | For FSK,Burst, Sweep |
| Level | TTL Compatible into 50Ω |
| Pulse Width | >450ns |
| Maximum Rate | 1MHz |
| Fan-out | ≥4 TTL Load |
| Impedance | 50Ω Typical |
Frequency Counter | | | |
| Range | 5Hz to 150MHz |
| Accuracy | Time Base accuracy±1count |
| Time Base | ±20ppm (23˚C ±5˚C) |
| Resolution | The maximum resolution is: 100nHz for 1Hz, 0.1Hz for 100MHz. |
| Input Impedance | 1kΩ/1pf |
| Sensitivity | 35mVrms ~ 30Vms (5Hz to 150MHz) |
| Ground Isolation | 42Vpk max |
Dual Channel Function(CH1/CH2) | | | |
| Phase | -180∘ ~180∘ |
| | Synchronize phase |
| Track | CH2=CH1 |
| Coupling | Frequency(Ratio or Difference) |
| | Amplitude & DC Offset |
| Dsolink | √ |
Save/Recall | | 10 Groups of Setting Memories |
Interface | | LAN(MFG 22XX Series only), USB |
Display | | 4.3’’ TFT LCD 480 × 3 (RGB) × 272 |
General Specifications | | |
| Power Source | AC100~240V, 50~60Hz or AC100~120V, AC220~240V, 50~60Hz |
| Power Consumption | 30W or 80W(With power amplifier) |
| Operating Environment | Temperature to satisfy the specification : 18 ~ 28˚C Operating temperature : 0 ~ 40˚C Relative Humidity: ≤ 80%, 0 ~ 40˚C ≤ 70%, 35 ~ 40˚C Installation category: CAT II |
| Operating Altitude | 2000 Meters |
| Pollution Degree | IEC 61010 degree 2, Indoor use |
| Storage Temperature | -10~70˚C, Humidity: ≤70% |
| Dimensions (WxHxD) | 266(W) x 107(H) x 293(D) mm |
| Weight | Approx. 2.5kg |
| Safety designed to | EN61010-1 |
| Accessories | GTL-101× 1(MFG-21XX) GTL-101× 2(MFG-22XX) |
| | Quick Start Guide ×1 CD (user manual + software) ×1 Power cord×1 |
| | | | | | | | | | | | | |