We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
The EXCUWE ELITEpro XC Energy Logger from DENT Instruments comes equipped with WiFi Communication and an external antenna. Part of DENT’s ELITEpro XC series, the EXCUWE can be applied to single or three-phase systems and is capable of measuring up to 4 channels of energy metrics with current ranges of 0-6000 amps. The process of monitoring current on each phase is a result of using direct connections to each phase of the voltage and several interchangeable CTs, such as split-core current transformers or the RoCoils. See the accessories tab for available DENT CTs.
In addition to monitoring, storing and analyzing electrical consumption data, the EXCUWE can capture kWh/kW energy, demand data and even electrical load diagnostic parameters, such as power factor (Apparent and Displacement).
The EXCUWE is equipped WiFi Communication capabilities and is fitted with an external 3 dbi antenna. The WiFi interface makes accessing the meter on any PC using the network simple via the ELOG Software. For even more communication capabilities, the EXCUWE can be configured as its own HotSpot, providing users the ability to see real-time data on any WiFi enabled PC, smartphone or tablet by way of a web browser.
TECHNICAL | |
Service Type | Single Phase (two wire or three wire), Three Phase-Four Wire (WYE), Three Phase-Three Wire (Delta), DC Systems (Solar/Battery) |
Voltage Channels | 3 channels, CAT III, 0-600 VAC (line-to-line) or 600 VDC* |
Current Channels | 4 channels, .67 VAC max, +/- 1 VDC. Ideal for 333 mV full scale CTs |
Maximum Current Input | External transducer dependent. 200% of current transducer rating (mV CTs) Measure up to 6000A with RoCoil CTs. |
Measurement Type | True RMS using high-speed digital signal processing (DSP) |
Line Frequency | DC/50/60 Hz* |
Waveform Sampling | 12 kHz |
Channel Sampling Rate | .125 seconds |
Integration Period | 1, 3, 15, 30 seconds; 1, 2, 5, 10, 15, 20, and 30 minutes; 1 and 12 hours, 1 day |
Energy Measurements | Volts, Amps, Amp-Hrs (Ah), kW, kWh, kVAR, kVARh, kVA, kVAh, Displacement Power Factor (dPF). All parameters for each phase and for system total. |
Analog Measurements | 0-10 Volts, 0-20 or 4-20 mA current loop. Non-isolated, external power for current loop. User scaling for sensor reporting in physical units. |
Accuracy | Better than 1% (<0.2% typical) for V, A, kW, kVAR, kVA, PF, Analog |
Resolution | 0.01 Amp, 0.001 Volt, 1 Watt, 1 VAR, 1 VA, 0.01 PF, 0.001 ANA |
LED Indicators | Tri-color (red, green, blue): 1 LED indicates communication (blue for wireless, Bluetooth® or Ethernet), 4 LEDs for correct phasing (PhaseChek™). |
POWER | |
Line-Power | From L1 Phase to L2 Phase. 80-600V (AC or DC) CAT III DC/50/60 Hz, 125 mA, 5 W, or 10 VA max. Non-user replaceable .5 Amp internal fuse protection. |
Power In | 6-10 VDC, 500 mA |
Power Out | 6 VDC, 200 mA max |
COMMUNICATIONS | |
USB (Standard) | USB standard (Type B). 1.8 M (6 ft) A-to-B USB Cable (included) |
Ethernet (Standard) | Standard RJ-45 Connector supports 10/100 MB Ethernet over Cat 5 or better. Configure for DHCP or Static IP. |
WI-FI Adapter | External 3 dbi antenna: typical range 150-300 ft. |
MECHANICAL | |
Operating Temperature | -7 to + 60 °C (20 to 140 °F) |
Operating Humidity | 5% to 95% non-condensing |
Enclosure Type | ABS plastic, 94-V0 flammability rating |
Weight | 340 g (12 ounces) |
Dimensions | 21.6 x 6.3 x 4.7 cm (8.5” x 2.5” x 1.9”) |
- • Verification Studies
- • Energy Audits
- • True RMS Current Reading
- • Energy Surveys
- • Load Profiling
Products In This Series
As low as
Now $1,865.00As low as
Now $1,650.00