0 to 20% of Range:
± (0.02% of Full Scale)
Includes all effects of linearity, hysteresis, repeatability, temperature, and stability for one year.
20% to 110% of Range:
± (0.1% of Reading)
All models indicate vacuum, but vacuum specification applies to 15 psi, 30 psi, 100psi, and 300psi models only.
± (0.25% of Full Scale*)
Not recommended for continuous use below -14.5 psi.
* Full Scale = -14.5 psig
Refer to XP2i-DP data sheet for gauges that are intended for continuous high vacuum use.
Vacuum to Full Scale
|S2 Option:||± (0.02% of Full Scale) 15 to 25° C|
± (0.05% of Full Scale) -10 to 15° C,
25 to 50° C, typical
|S5 Option:||± (0.05% of Full Scale) -10 to 50° C|
-10 to 50°C (14 to 122°F)
Non-condensing. No change in accuracy over operating temperature range. Gauge must be zeroed to achieve rated specification.
LCD readable in sunlight with bright backlight.
Single Line Display:
16.9 mm (0.67") high
PSV mode is intended for Pressure Safety Valve testing, and requires software to enable.
Dual Line Display:
Main Display: 13.9 mm (0.55")
4 readings/second (standard)
The XP2i is Intrinsically Safe only if powered by one of the following battery types.
|ATEX/IECEx:||Approved Battery Type||Ta=||Marking|
|Rayovac Max Plus 815||-20 to 50° C||Ex ia IIC T4 Ga|
|Energizer EN91||-20 to 50° C||Ex ia IIC T3 Ga|
|CSA:||Approved Battery Type||Ta=||Marking|
|Rayovac Max Plus 815||-20 to 45° C||Class I, Division 1, A, B, C, D T4|
|Energizer E91||-20 to 50° C||Class I, Division 1, A, B, C, D T3C|
|Rayovac Max Plus 815|
3 x AA:
1500 hours, typical
Uses 3 alkaline AA (LR6) batteries. Use of backlight and/or RS232 reduces operating time.
Optional AC power supply available. Do not use AC power supply in hazardous locations.
Ultra Low Power:
> 1 year, typical**
** 20 minute recording interval or greater in LT5 mode.
Free Labview drivers and programming instructions are available for download from website.
Do not use RS32 in hazardous locations.
32 000 data points
DataLoggerXP Firmware Update may be purchased at time of order, or in an Upgrade Package later.
Non-volatile flash memory
Software available for download from our website.
Compatible w/ 32 & 64 bit Windows 7, and Vista.
Produces csv files, or used Excel template files (samples included) to automatically format and graph data.
Min. Event Duration:
*** Logging Type - Average with Peaks.
562 g (19.8 oz)
Weight includes batteries.
|IP66 and IP67|
Submersible to 1 m for 30 minutes [IEC 60529].
Nickel plating over low copper, marine grade aluminum.
Keypad and Labels:
UV Resistant Polyester
LCD protected from impact damage by 1.5 mm (0.06") thick polycarbonate lens under polyester window.
316 stainless steel
All welded, with a permanently filled diaphragm seal.
and Viton internal o-ring (finger tight)
Metal to metal cone seal; O-ring can be removed if necessary.
Diaphragm Seal Fluid:
Optional connection on back.
Crystal CPF Female
1/4" male NPT adapter included unless BSP or M20 is specified.
1/4" medium pressure tube system compatible with HiP LM4 and LF4 Series, Autoclave Engr SF250CX Male and Female Series.
-40 to 75°C (-40 to 167°F)
Batteries should be removed if stored for more than one month.
The following requires the use of our free ConfigXP software.
User Defined Unit:
Allows the user to define and display any pressure units not included, or to use the gauge to display force, level, or other pressure related parameters. Reduce or increase displayed resolution.
Intended for pressure safety valve / burst disk testing. 8 readings per second. Captures point at which valve opens, as well as reseat pressure.
Smooths unsteady readings (1 to 10 samples).
Unwanted pressure units from Units button.
Peak pressure button.
Limit or Disable:
Changes to configuration or calibration factor(s).
Configuration to a file.
Configuration to other gauges.
Optional Pressure Pump Systems
A includes System A (pneumatic) 0 to 30 psi
AH includes System A (pneumatic) 0 to 580 psi
B includes System B (pneumatic) -25 inHg to 30 psi
BHincludes System B (pneumatic) -25 inHg to 580 psi
C includes System C (oil) 0 to 3,000 psi
CH includes System C (oil) 0 to 5,000 psi
DO includes System D (oil) 0 to 5,000 psi
DW includes System D (water) 0 to 5,000 psi
EOincludes System E (oil) 0 to 10,000 psi
FOVincludes System F (oil) 0 to 15,000 psi
FWVincludes System F (water) 0 to 15,000 psi
GOincludes System G (oil) 0 to 15,000 psi
GWincludes System G (water) 0 to 15,000 psi
HOincludes System H (oil/pneumatic) -25 inHg to 580 psi and 0 to 5,000 psi
*Not recommended for oxygen service
- Field gauge calibration
- Permanent outdoor installation
- Burst disc testing
- Pressure safety valve (PSV) testing
- Hydraulic torque wrench indication
- Torque datalogging
- Pressure regulator testing
- Pipeline static pressure testing
- Chart recorder replacement
- Wellhead monitoring
- Filter performance testing
- Hydrostatic leak testing
Products In This Series
As low asNow $1,541.00
As low asNow $3,369.00
As low asNow $1,702.00
As low asNow $1,541.00