Additel ADT760-MA-02 Pressure Calibrator

Pressure Specification
	760-LLP	760-D	760-MA
Max Pressure Range	±30 inH2O (75 mbar)	-12.5 to 35 psi (-0.86 to 2.5 bar)	-12.5 to 300 psig (-0.86 to 20 bar.g)
Accuracy	0.05%FS[1]	0.02%FS[1]	0.02%FS[1][3]
Stability	0.005%FS[2]	0.005%FS[2]	0.005%FS[2]
Pressure Type	Differential, Gauge	Differential, Gauge	Gauge, Absolute
Over Range Indication	120%
Resolution	6 digits
Measurement Units	Pa, hPa, kPa, mPa, bar, mbar, psi, mmHg@0°C, cmHg@0°C, mHg@0°C, inHg@0°C, inH2O@4°C, mmH2O@4°C, cmH2O@4°C, mH2O@4°C, mmH2O@20°C, cmH2O@20°C, mH2O@20°C, mH2O@68°F, inH2O@20°C, kgf/cm2, mtorr, torr, lb/ft2, tsi, custom
Barometric Accuracy	N/A	N/A	55 Pa[4]
Connection	Barb fitting	Hose, 5 ft (1.5 m), with built-in filter to 1/4BSPF, 1/4NPTF, and M20F adapters	Hose, 5 ft (1.5 m), with built-in filter to 1/4BSPF, 1/4NPTF, and M20F adapters
Pressure Output Rate	<30 Seconds (30 inH2O / 100 ml)	<10 Seconds (35 psi / 5 ml)	<90 Seconds (300 psi / 5 ml)
[1] FS specification applies to the span of the module range. [2] Stability based on FS of the internal pressure module. Stability is 0.005%FS or 0.05 pa whichever is greater. Internal module is switchable. [3] Specification based on gauge measurement. An additional 55 pa uncertainty will need to be included when measuring in absolute mode. [4] 55 Pa uncertainty (k=2) includes calibration uncertainty, linearity, and long-term stability (<30 Pa per year). Barometer range of 60 to 110 kPa.

Selection Guide - Differential Pressure
Module	Module Range[6]		Media	Accuracy (%FS)[1]	Burst Pressure	760-LLP	760-D	760-MA
Module	inH2O	mbar	Media	Accuracy (%FS)[1]	Burst Pressure	760-LLP	760-D	760-MA
DP025	±0.25	±0.62	G	0.2[2]	100x	•
DP050	±0.5	±1.25	G	0.1[3]	100x	•
DP1	±1	±2.5	G	0.05[4]	100x	•
DP2	±2	±5	G	0.05[4]	100x	•
DP5	±5	±10	G	0.05[4]	50x	•
DP10	±10	±25	G	0.05[4]	20x	•	•
DP20	±20	±50	G	0.05	20x	•	•
DP30	±30	±75	G	0.05	20x	•	•
DP50	±50	±125	G	0.05	3x		•
DP100	±100	±250	G	0.02	3x		•
DP150	±150	±350	G	0.02	3x		•
DP300	±300	±700	G	0.02	3x		•
DP400	-380 to 400	-950 to 1K	G	0.02	3x		•
DP800	-380 to 800	-950 to 2K	G	0.02	3x		•
DP1K	-380 to 1K	-950 to 2.5K	G	0.02	3x		•
[1] FS specification applies to the span of the module range. Accuracy includes one-year stability, except for DP025 to DP10 modules.
[2] Accuracy is a 6 months spec, 1-year long-term drift is 0.2%FS.
[3] Accuracy is a 6 months spec, 1-year long-term drift is 0.1%FS
[4] Accuracy is a 6 months spec, 1-year long-term drift is 0.05%FS.
[5] Specification based on gauge measurement. An additional 60 pa uncertainty will need to be included when measuring in absolute mode. Applicable only for use with the ADT760-MA
[6] The low module pressure range may be outside the pressure range of the calibrator
* ADT155 Pressure Modules are calibrated in psi and inH2O.

Selection Guide - Gauge Pressure
Module	Module Range[6]		Media	Accuracy (%FS)[1]	Burst Pressure	760-LLP	760-D	760-MA
Module	psi	bar	Media	Accuracy (%FS)[1]	Burst Pressure	760-LLP	760-D	760-MA
CP10	±10	±0.7	G	0.02[5]	3x		•	•
CP15	-13.5 to 15	-0.95 to 1	G	0.02[5]	3x		•	•
CP30	-13.5 to 30	-0.95 to 2	G	0.02[5]	3x		•	•
CP35	-13.5 to 35	-0.95 to 2.5	G	0.02[5]	3x		•	•
CP50	-13.5 to 50	-0.95 to 3.5	G	0.02[5]	3x			•
CP100	-13.5 to 100	-0.95 to 7	G	0.02[5]	3x			•
CP150	-13.5 to 150	-0.95 to 10	G	0.02[5]	3x			•
CP200	-13.5 to 200	-0.95 to 14	G	0.02[5]	3x			•
CP300	-13.5 to 300	-0.95 to 20	G	0.02[5]	3x			•
[1] FS specification applies to the span of the module range. Accuracy includes one-year stability, except for DP025 to DP10 modules.
[2] Accuracy is a 6 months spec, 1-year long-term drift is 0.2%FS.
[3] Accuracy is a 6 months spec, 1-year long-term drift is 0.1%FS
[4] Accuracy is a 6 months spec, 1-year long-term drift is 0.05%FS.
[5] Specification based on gauge measurement. An additional 60 pa uncertainty will need to be included when measuring in absolute mode. Applicable only for use with the ADT760-MA
[6] The low module pressure range may be outside the pressure range of the calibrator
* ADT155 Pressure Modules are calibrated in psi and inH2O.

Electrical Specification
	Range	Resolution	Accuracy	Note
mA Measure	±30 mA	0.0001 mA	0.01%RD+0.005%FS	Impedance<10Ω
V Measure	±30 V	0.0001 V	0.01%RD+0.005%FS	Impedance >1MΩ
mA Source	24 mA	0.001 mA	0.01%RD+0.005%FS	20 mA @ 1K
Loop Power Source	24 V	N/A	±1 V	50 mA (Max Loading)
Pressure Switch	Open, close. Support for mechanical switches and NPN/PNP digital switches.
Temperature Compensation	41°F to 95°F (5°C to 35°C)
Temperature Coefficient	< ± ( 0.001%RD + 0.001%FS ) / °C outside of 5°C to 35°C

General Specifications
Specification	Description
Channels	Four total: one electrical, one internal pressure, two external pressure (measure only)
Enclosure IP Rating	IP52 water and dust proof
Battery	Rechargeable Li-Ion battery, typically 10 hours of operation, recharges in less than 4 hours
Display	Color 800 x 480 TFT 5-inch touch screen
Communications	USB, WiFi
Weight	<4 lbs (<1.8 kg)
Size	9.3 x 4.3 x 2.8 in (235 x 110 x 70 mm)
Certification	ISO17025 accredited certificate with data included
HART Communications	Optional (ADT760-X-DL model)
Data Logging	Optional (ADT760-X-DL model), up to 1,000,000 readings (date and time stamped)
Task Documentation	Optional (ADT760-X-DL model) up to 1000 tasks
Automation Functions	Switch test, auto step, leak test
Misuse Protection	Up to 30 V on any two sockets
Multi Lingual Interface	English, German, French, Italian, Spanish, Portuguese, Chinese, Japanese, and Russian
Pump Life	>500,000 cycles
Power	Rechargeable Li-Ion battery, external power: 110/220 V power adapter 10 V
Environment Specifications	Operation: 32°F to 122°F (0°C to 50°C), 0-90% RH, less than 3,000 meters Compensated temperature: 32°F to 122°F (0°C to 50°C) Storage temperature: -4°F to 158°F (-20°C to 70°C)
Vibration and Shock	Vibration: 4g (20 to 2,000 Hz) Shock: 8g, 1 meter drop test
Compliance	CE
Software	ACal, PCal, Land, LogII
Warranty	1 year

Additel ADT760-MA-02 Automatic Handheld Pressure Calibrator (0.02% FS Accuracy)